Use of semi-permeable bag materials to facilitate on-site treatment of biological agent-contaminated waste.

Clean up following the wide-area release of a persistent biological agent has the potential to generate significant waste. Waste containing residual levels of biological contaminants may require off-site shipment under the U.S. Department of Transportation's (US DOT) solid waste regulations for Category A infectious agents, which has packaging and size limitations that do not accommodate large quantities. Treating the waste on-site to inactivate the bio-contaminants could alleviate the need for Category A shipping and open the possibility for categorizing the waste as conventional solid waste with similar shipping requirements as municipal garbage. To collect and package waste for on-site treatment, a semi-permeable nonwoven-based fabric was developed. The fabric was designed to contain residual bio-contaminants while providing sufficient permeability for penetration by a gaseous decontamination agent. The nonwoven fabric was tested in two bench-scale experiments. First, decontamination efficacy and gas permeability were evaluated by placing test coupons inoculated with spores of a Bacillus anthracis surrogate inside the nonwoven material. After chlorine dioxide fumigation, the coupons were analyzed for spore viability and results showed a ≥6 Log reduction on all test materials except glass. Second, filters cut from the nonwoven material were tested in parallel with commercially available cellulose acetate filters having a known pore size (0.45 µm) and results demonstrate that the two materials have similar permeability characteristics. Overall, results suggest that the nonwoven material could be used to package waste at the point of generation and then moved to a nearby staging area where it could be fumigated to inactivate bio-contaminants.

Monitoring spore washoff during a biological contamination incident response using automated stormwater samplers and sensors to predict contamination movement.

This study examined the washoff of Bacillus globigii (Bg) spores from concrete, asphalt, and grass surfaces by stormwater. Bg is a nonpathogenic surrogate for Bacillus anthracis, which is a biological select agent. Areas (2.74 m × 7.62 m) of concrete, grass, and asphalt were inoculated twice at the field site during the study. Spore concentrations were measured in runoff water after seven rainfall events (1.2-65.4 mm) and complimentary watershed data were collected for soil moisture, depth of water in collection troughs, and rainfall using custom-built telemetry units. An average surface loading of 107.79 Bg spores/m2 resulted in peak spore concentrations in runoff water of 102, 260, and 4.1 CFU/mL from asphalt, concrete, and grass surfaces, respectively. Spore concentrations in the stormwater runoff were greatly reduced by the third rain event after both inoculations, but still detectable in some samples. When initial rainfall events occurred longer after the initial inoculation, the spore concentrations (both peak and average) in the runoff were diminished. The study also compared rainfall data from 4 tipping bucket rain gauges and a laser disdrometer and found they performed similarly for values of total rainfall accumulation while the laser disdrometer provided additional information (total storm kinetic energy) useful in comparing the seven different rain events. The soil moisture probes are recommended for assistance in predicting when to sample sites with intermittent runoff. Sampling trough level readings were critical to understanding the dilution factor of the storm event and the age of the sample collected. Collectively the spore and watershed data are useful for emergency responders faced with remediation decisions after a biological agent incident as the results provide insight into what equipment to deploy and that spores may persist in runoff water at quantifiable levels for months. The spore measurements are also a novel dataset for stormwater model parameterization for biological contamination of urban watersheds.

Assessment of a regulatory measurement system for the determination of the non-volatile particulate matter emissions from commercial aircraft engines.

The SAE International has published Aerospace Information Report (AIR) 6241 which outlined the design and operation of a standardized measurement system for measuring non-volatile particulate matter (nvPM) mass and number emissions from commercial aircraft engines. Prior to this research, evaluation of this system by various investigators revealed differences in nvPM mass emissions measurement on the order of 15-30% both within a single sampling system and between two systems operating in parallel and measuring nvPM mass emissions from the same source. To investigate this issue, the U. S. Environmental Protection Agency in collaboration with the U. S. Air Force's Arnold Engineering Development Complex initiated the VAriable Response In Aircraft nvPM Testing (VARIAnT) research program to compare nvPM measurements within and between AIR-compliant sampling systems used for measuring combustion aerosols generated both by a 5201 Mini-CAST soot generator and a J85-GE-5 turbojet engine burning multiple fuels. The VARIAnT research program has conducted four test campaigns to date. The first campaign (VARIAnT 1) compared two essentially identical commercial versions of the sampling system while the second campaign (VARIAnT 2) compared a commercial system to the custom-designed Missouri University of Science and Technology's North American Reference System (NARS) built to the same specifications. Comparisons of nvPM particle mass (i.e., black carbon), number, and size were conducted in both campaigns. Additionally, the sensitivity to variation in system operational parameters was evaluated in VARIAnT 1. Results from both campaigns revealed agreement of about 12% between the two sampling systems, irrespective of manufacturer, in all aspects except for black carbon determination. The major source of measurement differences (20-70%) was due to low BC mass measurements made by the Artium Technologies LII-300 as compared to the AVL 483 Micro-Soot Sensor, the Aerodyne Cavity Attenuated Phase Shift (CAPS PMSSA) monitor, and the thermal-optical reference method for elemental carbon (EC) determination, which was used as the BC reference.

Capture of methyl bromide emissions with activated carbon following the fumigation of a small building contaminated with a Bacillus anthracis spore simulant.

A wide-area Bacillus anthracis spore contamination incident will present immense challenges related to decontamination capacity. For this reason, fumigation with methyl bromide (MeBr) has been proposed as a potential remediation option. Although a few bench-scale laboratory studies have been conducted to evaluate activated carbon for the capture of MeBr, these studies were conducted at conditions replicating commodity fumigation using relatively low MeBr concentrations, temperatures, and/or relative humidity (RH) levels. The more rigorous MeBr fumigation requirements to fully inactivate B. anthracis spores are much more of a challenge for an activated carbon system (ACS) to capture MeBr, and warrant their own investigation. Further, while the aforementioned studies have shown activated carbon to be a possible option for the capture of MeBr in gas streams, these tests were conducted at laboratory bench scale, and thus lack operational perspective and data. Thus, we present for the first time the results of a full-scale study to evaluate an ACS employed for the capture of MeBr at conditions that would be used for decontaminating a building structure contaminated with B. anthracis spores. Airflow rate, temperature, RH, and MeBr levels were measured within the ACS during its operation. Despite the relatively high humidity, temperature, and MeBr levels, the MeBr capture efficiency of the ACS was demonstrated to be more than 99%. The concentration of MeBr exhausted from the structure was reduced from 41,000 to 136 ppmv in 3.5 hr, corresponding to an overall atmospheric emission rate of less than 2 kg. The practical adsorption rate of the ACS was determined to be 4.83 kg MeBr/100 kg carbon. The information and data presented here will facilitate future use of this technology when fumigating with MeBr.